E5013 Fast Set Clear Epoxy Primer WB Concrete | Wood | Masonry

Description

E5013 Fast Set Clear Epoxy Primer WB Concrete | Wood | Masonry
E5013 Fast Set Epoxy Primer WB
E5013 Fast Set Epoxy Clear Primer WB is a water based 2 component epoxy penetrating clear primer coating with superb chemical resistance, abrasion resistance and substrate penetration. Has excellent adhesion with 425 psi. When used as a primer coat for, epoxy, polyaspartic and urethane coating systems can help prevent damage (bubbles and air pockets) to the topcoat from concrete outgassing.
As a fast setting epoxy, E5013 allows application of topcoat same day and can support foot traffic in 6-12 hours.
Comes in a gloss clear finish. The clear is not water clear and not suitable as a final topcoat over previously color coated floors.
Available in a quart kit, 1 gallon kit, 2 gallon kit and 5 gallon kit. For areas subject to constant exposure to water or high humidity, consider using our
AM5015 Anti-Microbial Mildew Resistant Epoxy Primer
PRIMER:
None required
TOPCOAT:
Many products are suitable as topcoats including epoxy, urethane and polyaspartic coating systems.
Where is E5013 Fast Set Epoxy Primer WB used?
Concrete
Masonry
Wood
Why E5013 Epoxy Primer?
Versatile product good on concrete, masonry, wood surfaces
Quick 4-6 hour Recoat for same day projects
Excellent as clear primer for epoxy, polyaspartic and urethane coating systems
Helps prevent concrete outgassing problems when used as primer
Long 2 hour pot life
Excellent adhesion 425 psi
Good chemical and abrasion resistance
Water base
SPECIFICIATIONS
Solids
By Weight 43% By Volume 40%
VOC
250 g/L
Colors
Clear (not water clear - suitable as a primer or concrete sealer only)
Recommended Film Thickness
5-7 mils wet, 2-3 mils dry
Coverage per Gallon
229 - 320 sq'/gal @5-7 mils wet thickness
Packaging
quart, 1 gallon kit, 2 gallon kit, 5 gallon kit
Mix Ratio
4:1 .8 gallons part A per .2 gallons part B by volume
Shelf Life
1 year in unopened container
Finish
Gloss > 60 @60 degrees glossmeter
Abrasion Resistance
Tabor abrasor CS-17 wwheel with 1000 gram total load and 500 cycles = 45 mg loss
Impact Resistance
Gardner impact, direct = 50 in. lb (passed)
Flexibility
No cracks on a 1/8" mandre
Adhesion
425 psi @ecometer (concrete failure, no delamination)
Viscosity
Mixed = 400 - 900 cps (typical)
CURE SCHEDULE
Pot Life - 1 gallon volume
2 hours (at 75F)
Tack Life (dry to touch)
2 - 4 hours
Recoat or Topcoat
4 - 6 hours
Light foot traffic
6 - 12 hours
Full cure (heavy traffic)
2 - 5 days
APPLICATION TEMPERATURE:
55-90 degrees F with relative humidity below 75%
CHEMICAL RESISTANCE
RATING
acetic acid 5%
B
xylene
B
mek
A
gasoline
B
10% sodium hydroxide
C
50% sodium hydroxide
B
10% sulfuric
B
10% hydrochrolic acid
B
20% nitric acid
A
ethylene gylycol
C
Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term splash spill, D - 72 hour immersion, E - long term immersion.
MIXING AND APPLICATION INSTRUCTIONS
PRODUCT STORAGE:
Store product in an area so as to bring the material to normal room temperature before using. Continuous storage should be between 60 and 90 degree F. Keep from freezing.
SURFACE PREPARATION
: Surface preparation will vary according to the type of complete system to be applied. For a one or two coat thin build system (3-10 mils dry) we recommend either mechanical scarification or acid etching until a suitable profile is achieved. For a complete system build higher than 10 mils dry, we recommend a fine brush blast (shot blast). All dirt, oil, dust, foreign contaminants and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the concrete has an appropriate vapor barrier. This can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate does not show signs of eventual hydrostatic pressure problems that may later cause disbanding. However, this product can be applied to a damp floor as long as there are not standing puddles.
PRODUCT MIXING
: This product comes pre-packaged by weight. Kits should be mixed in their entirety. If partial kits are to be used, refer to the front of this technical data for proper weight mix ratios. After the two parts are combined, mixes well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. This product is an emulsion product and should be mixed well before. Improper mixing may result in product failure. For best mixing results and proper blending of parts A and B, recommend a
Jiffy Mixer
style drill mixer.
PRODUCT APPLICATION
: The mixed material can be applied by brush or roller. Maintain temperatures within the recommended ranges during the application and curing process. Apply material with relative humidity within the parameters shown on the technical data. When the end of the pot life has been reached, you will find that the material becomes hard to apply and will actually tend to roll back up onto the roller. Do not try to continue application when the coating has reached this step. Applications made at different times with differing environmental conditions, may show slight variations in gloss.
RECOAT OR TOPCOATING:
If you opt to recoat or topcoat this product, you must first be sure that all of the solvents and water have evaporated from the coating during the curing process. The information on the front side are reliable guidelines to follow. However, it is best to test the coating before recoating or topcoating. This can be done by pressing on the coating with your thumb to verify that no fingerprint impression is left. If no impression is created, then the recoat or topcoat can be started. Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. Before recoating or topcoating, check the coating to insure no epoxy blushes were developed (a whitish, greasy film or deglossing). If a blush is present, it must be removed prior to topcoating or recoating. A standard type detergent cleaner can be used to remove any blush. Many epoxy overlays and coatings as well as urethanes are compatible for use as a topcoat for this product as well as multiple coats of this product.
CLEANUP
: Use PM solvent
FLOOR CLEANING:
Caution! Some cleaners may affect the color of the floor installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested.
RESTRICTIONS
: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data under full cure). It is best to let the floor remain dry for the full cure cycle. Dependent on actual complete system application, surface may be slippery, especially when wet or contaminated; keep surface clean and dry.
LIMITATIONS:
Color or gloss may be affected by humidity, low temperatures, chemical exposure or sodium vapor lighting.
Product will yellow in the presence of UV light
For best results use a 1/4” or 3/8” nap roller.
Slab on grade requires moisture barrier
Substrate temperature must be 5°F above dew point.
All new concrete must be cured for at least 30 days
Improper mixing or too thick of an application may result in product failure
Physical properties listed on this technical data sheet are typical values and not specifications.
See tab for application instructions.
See Application tab for limitations of our liability and warranty
NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY
We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products
Size
Color
Price
1 Quart Trial Size Kit
Clear (Not Water Clear)
$
57.20
5 Gallon Kit
Clear (Not Water Clear)
$
400.40
2 Gallon Kit
Clear (Not Water Clear)
$
188.76
1 Gallon Kit
Clear (Not Water Clear)
$
97.24
Shipping
Shipping cost:
No cost shipping lower 48 US States FedEx Ground
Delivery time:
Delivery 1 to 5 days after shipment depending on location
Payment
We accept the following payment methods:
PayPal payment due at time of order placement
Please contact us if you have any questions.
Service
PLEASE CONTACT CUSTOMER SERVICE FOR QUESTIONS