BEVEL GEAR AND SHAFT SET- KEARNEY TRECKER-CINCINNATI (W4)

Description

(W4) THIS IS A NEW NEVER USED BEVEL (90 DEGREE) GEAR AND SHAFT SET. IT'S BEEN A LONG TIME SINCE I'VE LOOKED AT THEM, BUT I THINK THEY ARE EITHER FOR A KEARNEY TRECKER SIMPLEX MILL OR A CINCINNATI CENTERLESS
. I'M FAIRLY SURE THEY'RE NOT CINCINNATI. THERE IS SOME LIGHT CORROSION ON THEM, BUT IT WILL IN NO WAY AFFECT SERVICEABILITY. IF YOU NEED  MORE OR BETTER PHOTOS, LET ME KNOW. I'LL TRY TO DESCRIBE THESE SO THERE'S NO QUESTION OF WHAT THEY MEASURE OUT TO. THEY WERE MADE PROBABLY BY GROVE GEAR OR ILLINOIS GEAR. BOTH WERE OWNED BY REGAL BELOIT AND THEY MADE THESE FOR ONE OF OUR MILLS, I BELIEVE. MATERIAL IS 8620.
THE SHAFT IS 14.2 +/- INCHES LONG. USING CALIPERS, THE SPLINE IS 1.500 DIAMETER, 6 GROOVE, THE MINOR DIAMETER IS 1.273 . THE WIDTH OF THE 'TOOTH' IS .365 .
THE END OF THE SHAFT HAS A 2 INCH DEEP HOLE, SLIGHTLY RECESSED AND  THREADED 1/2 X 13 RIGHT HAND.  THE LENGTH OF THE SPLINE TO THE THREAD IS ABOUT 8-7/8 INCHES. THE THREAD MEASURES 1.725 (PROBABLY 1-3/4 NOMINAL) WITH 18 TPI. THREAD IS A BIT OVER 1 INCH LONG ENDING AT A SMALL UNDERCUT. SPLINE RUNS UP INTO THE THREAD, NEARLY ALL THE WAY THRU.
THE BEARING JOURNAL IS 3-1/8 LONG AND MEASURES 1.733 _/- AND TERMINATES AT A TRUED SHOULDER MEASURING 2-1/4 OD. THE GEAR 'HEAD' MEASURES .765 THICK,  X 4.850 DIAMETER. THE BACK ANGLE ON THE GEAR MEASURES ABOUT 34 DEGREES OFF STRAIGHT, THE FACE SIDE MEASURES ABOUT 30 DEGREES OFF THE FLAT END. SMALL DIAMETER ON THE FLAT END MEASURES AROUND 3-3/4. THE GEAR HAS 39 TEETH WHICH MEANS MY DIAMETER MEASUREMENT WILL BE A BIT OFF.
THERE IS A KEYWAY, .348 WIDE THAT IS IN LINE WITH ONE OF THE SPLINE GROOVES AND EXTENDS TO WITHIN ABOUT 1-5/16 OF THE SHOULDER.
THE MATING SMALLER GEAR MEASURES 3.385 OD AND HAS 26 TEETH. OVERALL THICKNESS IS 2.035. THERE IS A THRU INTERNAL SPLINE THAT MEASURES 1.352 +/- MAJOR ID AND 1.143 MINOR ID. WIDTH OF THE SPLINE GROOVE IS .320. FACE OF GEAR  HAS A SHOULDER THAT MEASURES 1.880 DIAMETER AND IS ABOUT 1/8 HIGH.  WIDTH OF THE GEAR SECTION IS ABOUT 7/8 WITH A SHOULDER ON THE BACK SIDE 2.730 DIAMETER BY ABOUT .140 HIGH. THE HUB ON THE BACK SIDE IS ABOUT 2.227 DIAMETER X .840 HIGH.
THERE IS SOME ETCHING ON THE SMALL GEAR THAT IS LIKELY NOT THE PART ID BUT READS: 87-800P  00041  BL.006. THE SHAFT IS MARKED BL006 0004L K7 87 800G.
UNLESS OTHERWISE STATED, WE WARRANT OUR ITEMS FOR 30 DAYS AFTER SHIPPING.  INSPECT THE ITEM AND IF YOU FIND IT UNSATISFACTORY OR HAVE ANOTHER ISSUE,  CONTACT US VIA EBAY MESSAGING  REGARDING RETURNING THE  ITEM FOR A REFUND OR POSSIBLE EXCHANGE.
IF YOU USE THE TOOL, IT IS NOT RETURNABLE.
WE VALUE OUR GOOD FEEDBACK RATING AND STRIVE TO MAINTAIN IT.
NORMALLY,   BUYER PAYS RETURN POSTAGE AND REFUND MAY BE FOR
PRICE  PAID MINUS SHIPPING CHARGES.
WE ACCEPT PAYPAL ONLY UNLESS OTHERWISE ARRANGED
.
PAYMENT MUST BE RECEIVED WITHIN 7 DAYS OF SALE OR WE WILL CONSIDER NON-PAYING BUYER- UNLESS OTHERWISE ARRANGED.
INDIANA RESIDENTS-ADD 7% FOR SALES TAX OR PROVIDE T.I.D.
REASONABLE BEST OFFERS CONSIDERED. IF YOU NEED MORE THAN WE HAVE LISTED, LET US KNOW AND WE’LL SEE IF WE CAN ACCOMMODATE YOUR NEEDS.
WE GENERALLY SHIP WITHIN 24 HOURS OF PAYMENT, WEEKENDS AND HOLIDAYS EXCLUDED.
ON INTERNATIONAL SHIPMENTS, PLEASE ALLOW TIME FOR ITEMS TO CLEAR CUSTOMS.
PLEASE CHECK OUR OTHER ITEMS IN OUR STORE, IF YOU DON’T SEE WHAT YOU NEED, LET US SEE IF WE CAN FIND IT FOR YOU .